|
Title: Adding FoC Post by: BrainySmurf on August 27, 2012, 10:44:55 AM Hey guys,
I have ordered a saber with MLS and a quick disconnect. Can I at a later date add FoC by simply purchasing a MLS with FoC and quick disconnect? Or would i have to add a cable to connect to the Obsidian? Or would I have to run completely new wires to the Obsidian? Or how would I get round this? Thanks :) Title: Re: Adding FoC Post by: Vex on August 27, 2012, 01:54:21 PM You will need to order a MLS with FoC , it will come with the connector you need to enable FoC. You will need to solder and heatshrink the one wire from the FoC connector to the FoC lead from the Obsidian. I added a wire diagram to the forum , it should help.
http://www.saberforum.com/index.php?topic=8667.0 (http://www.saberforum.com/index.php?topic=8667.0) Title: Re: Adding FoC Post by: BrainySmurf on August 27, 2012, 02:07:26 PM Awesome :D Thanks Vex.
Doesn't look too hard (of course I've not opened it up yet). But wiring wise looks very easy :) Title: Re: Adding FoC Post by: Master Bluespike74 on August 29, 2012, 02:25:47 AM Hey Brainy,
I have a video diary on my Overlord in the video section showing how the setups look different & how they operate when connected. If you are curious, you could stop by and check it out. Blue Title: Re: Adding FoC Post by: Jabari on October 04, 2012, 04:49:29 AM Hi. I have the same question, but I'm not sure I understand the answer above. Please bear with me.
Let's say I buy a Shock in orange with sound but no flash on clash. Later, I buy an extra MLS unit in silver WITH flash on clash. Can I put this second MLS unit in the same hilt, even though the original did not have flash on clash? Does the MLS just click in? I have almost no experience with electronics. It sounds like there's a part that would have to be soldered to add the flash on clash capability. How difficult is that? and once it's done, can the units still be switched out, or is it a permanent change? (I am unable to watch all the videos mentioned above right now, so they may help. I'm just not understanding the concept very well.) Thanks for your help. Title: Re: Adding FoC Post by: Master Bluespike74 on October 04, 2012, 11:31:33 AM Hi. I have the same question, but I'm not sure I understand the answer above. Please bear with me. Let's say I buy a Shock in orange with sound but no flash on clash. Later, I buy an extra MLS unit in silver WITH flash on clash. Can I put this second MLS unit in the same hilt, even though the original did not have flash on clash? Does the MLS just click in? I have almost no experience with electronics. It sounds like there's a part that would have to be soldered to add the flash on clash capability. How difficult is that? and once it's done, can the units still be switched out, or is it a permanent change? (I am unable to watch all the videos mentioned above right now, so they may help. I'm just not understanding the concept very well.) Thanks for your help. You can add an MLS unit with FOC to a saber without it but it requires some soldering skills. I always recommend getting the saber with FOC first so that if you wanted to add an MLS without it, it is easier. Quick disconnects make the process much easier. They are Red and Black connectors that simply plug into each other. If you do not have quick disconnects, the change is permanent until you cut and resolder. In the end, my recommendations are: 1. Get your saber with FOC. 2. Get your saber with Quick Disconnects. This makes changing LED units much easier, faster, and you don't run the risk of burning your fingers. Title: Re: Adding FoC Post by: Jabari on October 05, 2012, 05:25:51 AM Thank you! That was very helpful. :)
|