|
Title: Ultrasaber launcher Post by: Romale on March 23, 2021, 02:45:49 PM I’m totally new to this site and got my first saber, Diamond saber, I totally am happy with it thus far. I’m looking through the site and I’m not sure where to go to find the launcher. I’m sure that I will laugh about how easy it was to find if someone would help to tell me where I need to go to get it
Title: Re: Ultrasaber launcher Post by: Cyclops942 on March 23, 2021, 06:40:54 PM Look at the sticky threads in this forum (The Obsidian Order). Whether you need the Windows version or the Mac version, there is a thread for you.
Title: Re: Ultrasaber launcher Post by: MercuryKungFu on April 20, 2021, 05:58:08 AM I would suggest using it on a Windows system with USB 2.0 and not USB 3.0.
Title: Re: Ultrasaber launcher Post by: VFX_Jonny on October 06, 2021, 08:16:41 PM Can anyone help?
This is quite literally the first ever forum I have been on and I find it incredibly hard to Navigate to find answers. I've bought my first ever Ultra Saber, one that is equipped with a diamond controller, I managed to find the launcher (UltraSabers Launcher v2.45) and installed. No matter what I do, it is not picking up the lightsaber, its just says constantly "Device disconnected. Auto-connection enabled. Check if the board is powered by the battery pack, turned on and connected to your computer. If it still can't connect, try to unplug and replug the USB cable and/or restart the board" I installed with it connected and powered on, I have turned it off and on again, run in admin mode, uninstalled and reinstalled the launcher, trying with it connected and unconnected, I have recharged the batteries, and still absolutely nothing. Is there anything I am missing? Can anyone help? Thanks in advanced. Title: Re: Ultrasaber launcher Post by: KaiserSosay on October 06, 2021, 08:52:27 PM Can anyone help? This is quite literally the first ever forum I have been on and I find it incredibly hard to Navigate to find answers. I've bought my first ever Ultra Saber, one that is equipped with a diamond controller, I managed to find the launcher (UltraSabers Launcher v2.45) and installed. No matter what I do, it is not picking up the lightsaber, its just says constantly "Device disconnected. Auto-connection enabled. Check if the board is powered by the battery pack, turned on and connected to your computer. If it still can't connect, try to unplug and replug the USB cable and/or restart the board" I installed with it connected and powered on, I have turned it off and on again, run in admin mode, uninstalled and reinstalled the launcher, trying with it connected and unconnected, I have recharged the batteries, and still absolutely nothing. Is there anything I am missing? Can anyone help? Thanks in advanced. Are you positive you are using a DATA cable? You must use a data cable not just a simple power cable. That's usually the first problem people encounter. Title: Re: Ultrasaber launcher Post by: VFX_Jonny on October 06, 2021, 09:02:48 PM The cable I am using is the cable provided with the saber.
Is this not a data cable? Title: Re: Ultrasaber launcher Post by: KaiserSosay on October 06, 2021, 09:23:40 PM If you bought the cable with your saber it should be a data transfer cable. Should be.
Title: Re: Ultrasaber launcher Post by: Cyclops942 on October 07, 2021, 02:23:04 PM If you bought the cable with your saber it should be a data transfer cable. Should be. Notice the emphasis… try another cable, just to be sure. Every once in a while, even new cables break, or are defective. The one I got was one of these, and I spent a long time trying various ports on my computer, different USB hubs, and tearing out what little hair I had left, and I finally tried a different cable, and that worked. |