mmosca57
Force Sensitive
Force Alignment: 0
Posts: 5
|
 |
« on: November 09, 2017, 03:54:25 AM » |
|
I have installed and updated the UltraSaber Launcher app on my mac. My saber is powered on and I connected the USB cable to the computer. The saber program is not recognizing that my saber is connected to it. I have tried powering the saber on and off and re-connecting the USB. Any ideas?
|
|
|
|
|
Logged
|
|
|
|
|
Lady Agana Kath
Knight Commander
Force Alignment: -2130
Posts: 2857
Go Red or Go Home
|
|
« Reply #1 on: November 09, 2017, 03:18:28 PM » |
|
is is a 2.0 usb or 3.0? I do believe it works better with a 2.0 usb cable
|
|
|
|
|
Logged
|
|
|
|
|
mmosca57
Force Sensitive
Force Alignment: 0
Posts: 5
|
|
« Reply #2 on: November 12, 2017, 04:42:15 AM » |
|
I have tried 3 of my own USB 2.0 cables as well as the USB 2.0 cable I purchased from the UltraSaber website when I ordered the Saber. Still no luck getting the Saber Launcher Program to recognize that my Saber is attached.
|
|
|
|
|
Logged
|
|
|
|
|
Lady Agana Kath
Knight Commander
Force Alignment: -2130
Posts: 2857
Go Red or Go Home
|
|
« Reply #3 on: November 12, 2017, 02:40:39 PM » |
|
Try charging the batteries, if they are getting low it won't connect
|
|
|
|
|
Logged
|
|
|
|
|
skribs
Knight Templar
Force Alignment: 151
Posts: 304
|
|
« Reply #4 on: November 12, 2017, 09:34:29 PM » |
|
I had a similar problem on my PC. Rebooting my computer helped.
|
|
|
|
|
Logged
|
|
|
|
|
mmosca57
Force Sensitive
Force Alignment: 0
Posts: 5
|
|
« Reply #5 on: November 14, 2017, 09:23:15 PM » |
|
I tried restarting the computer and program. Still no luck. I am beginning to think the Saber board has a problem.
|
|
|
|
|
Logged
|
|
|
|
|
Racona Nova
Knight of the Obsidian Order
SaberForum.Com Moderator
Knight Commander
Force Alignment: 1116
Posts: 4771
There is no good or evil....there's only power!
|
|
« Reply #6 on: November 14, 2017, 09:59:22 PM » |
|
Try charging the batteries, if they are getting low it won't connect
Did you try that, too? |
|
|
|
|
Logged
|
Sig by Master Nero Phantasm v3 LE (Obs v3) - AB w/ FoC AS---Manticore (Obs v3) - BR w/ FoC AS (QD)---Archon v2.1 (Obs v3) - RGBW Emerald |
|
|
|
mmosca57
Force Sensitive
Force Alignment: 0
Posts: 5
|
|
« Reply #7 on: November 18, 2017, 02:12:43 AM » |
|
Yes, the first thing I did when I received my saber was make sure the batteries were charged all the way.
|
|
|
|
|
Logged
|
|
|
|
|
GonzoCubs
Knight Aspirant
Force Alignment: 6
Posts: 15
|
|
« Reply #8 on: November 19, 2017, 02:31:14 PM » |
|
Was your saber plugged in when you installed the launcher? I missed that instruction my first time installing and had to uninstall and reinstall with it plugged in everything to get it to work. I also had an issue that the USB cable I had tried to use was not a data cable, charging only, and the launcher won't connect to the saber without a data cable. I didn't even know there were different kinds of USB cable, but if you're using the one you got from US, I would think that would be the right cable.
|
|
|
|
|
Logged
|
|
|
|
|
mmosca57
Force Sensitive
Force Alignment: 0
Posts: 5
|
|
« Reply #9 on: November 27, 2017, 04:33:01 PM » |
|
Ok I finally got it sorted out. I re-downloaded the launcher with the saber connected and on, then i ran the maintenance tool, and then the firmware update immediately after.
On a slightly different topic:
Any ideas on how to "calm" the saber down? It has way too many effects while swinging it around for my taste.
|
|
|
|
|
Logged
|
|
|
|
|
Racona Nova
Knight of the Obsidian Order
SaberForum.Com Moderator
Knight Commander
Force Alignment: 1116
Posts: 4771
There is no good or evil....there's only power!
|
|
« Reply #10 on: November 27, 2017, 08:29:16 PM » |
|
You can change the sensor sensitivity settings in the Launcher. The ones you have to look at are Motion Thresold and Motion Integration Time for swings and Impact Thresold and Impact Debouncing Time for impacts/clashes/hits.
|
|
|
|
|
Logged
|
Sig by Master Nero Phantasm v3 LE (Obs v3) - AB w/ FoC AS---Manticore (Obs v3) - BR w/ FoC AS (QD)---Archon v2.1 (Obs v3) - RGBW Emerald |
|
|
|
|
