Welcome,
Guest
. Please
login
or
register
.
March 28, 2024, 10:38:30 AM
Click here for lightsabers
Click here for lightsabers
Saber Forum
|
Ultra Sabers Discussion
|
The Obsidian Order
|
Obsidian Technical Discussion
(Moderator:
Racona Nova
) |
The different Obsidian board settings and what they affect
Pages: [
1
]
Go Down
Send this topic
|
Print
Author
Topic: The different Obsidian board settings and what they affect (Read 14016 times)
Racona Nova
Knight of the Obsidian Order
Moderator
Knight Commander
Force Alignment: 1116
Posts: 4771
There is no good or evil....there's only power!
The different Obsidian board settings and what they affect
«
on:
September 24, 2016, 08:24:52 PM »
Since there are more and more questions on what the different Obsidian settings mean and what they affect, here's a short but simple explanation of any of the settings:
Motion Threshold: Overall sensitivity of the motion detection sensor. The lower the number, the more sensitive the sensor is - and the higher is the triggering of fake motion sounds.
Motion Integration Time: Sensitivity of the motion sensor in regards of the above mentioned fake triggers. The lower the number, the more sensitive the saber is and more fake triggers occur. Rising the number lowers the fake trigger chance, but also overall sensitivity. Use this in combination with Motion Threshold to achieve high sensitivity without too many fake triggers.
Impact Thresold: The same as Motion Thresold, only for the impact detection sensor.
Impact Debouncing Time: The same as Motion Integration Time, only for fake triggers of the impact sensor.
Minimum Time Between Impacts: This sets the reset speed of the impact sensor. The lower the number, the faster the sensor can react to subsequent impacts.
Lockup Flash Time (only for Flash on Clash
enabled
sabers
without
the Emerald Driver): The simplest of the settings. It controls the speed of the lockup light effects - the higher, the faster.
«
Last Edit: March 30, 2018, 06:05:15 PM by Racona Nova
»
Logged
Sig by Master Nero
Phantasm v3 LE (Obs v3) - AB w/ FoC AS---Manticore (Obs v3) - BR w/ FoC AS (QD)---Archon v2.1 (Obs v3) - RGBW Emerald
Gar-Wi Musan
Knight Major
Force Alignment: 102
Posts: 389
Re: The different Obsidian board settings and what they affect
«
Reply #1 on:
March 30, 2018, 10:23:32 AM »
Quote from: Racona Nova on May 08, 2017, 07:13:57 PM
*renewing request to sticky this thread*
I second that request.
Thank's for posting this.
Logged
Dauntless Seven
Lady of the Sage Order
Knight Commander
Force Alignment: 2037
Posts: 5444
Re: The different Obsidian board settings and what they affect
«
Reply #2 on:
March 30, 2018, 04:57:24 PM »
Hi Rac. I'm a tad late in catching this... but here's your sticky. Valuable information provided. Thanks.
point for you and Gar for bringing this to the Mod's attention
Logged
Racona Nova
Knight of the Obsidian Order
Moderator
Knight Commander
Force Alignment: 1116
Posts: 4771
There is no good or evil....there's only power!
Re: The different Obsidian board settings and what they affect
«
Reply #3 on:
March 30, 2018, 06:04:32 PM »
Thanks, D...almost forgot that this request was still there
Could have done that myself if I would've remembered
Logged
Sig by Master Nero
Phantasm v3 LE (Obs v3) - AB w/ FoC AS---Manticore (Obs v3) - BR w/ FoC AS (QD)---Archon v2.1 (Obs v3) - RGBW Emerald
Dauntless Seven
Lady of the Sage Order
Knight Commander
Force Alignment: 2037
Posts: 5444
Re: The different Obsidian board settings and what they affect
«
Reply #4 on:
March 30, 2018, 06:16:23 PM »
You are welcome.
I know that... but thought that perhaps with your humility that you didn't want to do this.
Logged
Racona Nova
Knight of the Obsidian Order
Moderator
Knight Commander
Force Alignment: 1116
Posts: 4771
There is no good or evil....there's only power!
Re: The different Obsidian board settings and what they affect
«
Reply #5 on:
March 30, 2018, 06:24:09 PM »
Oh you...lovely
Getting off-topic again....
Logged
Sig by Master Nero
Phantasm v3 LE (Obs v3) - AB w/ FoC AS---Manticore (Obs v3) - BR w/ FoC AS (QD)---Archon v2.1 (Obs v3) - RGBW Emerald
Blade Runner 62
Force Sensitive
Force Alignment: 0
Posts: 3
Re: The different Obsidian board settings and what they affect
«
Reply #6 on:
October 26, 2022, 04:47:22 PM »
Thank you for putting this info out there. I just picked up my Fallen with the V4 board and was looking for this.
Logged
Pages: [
1
]
Go Up
Send this topic
|
Print
Jump to:
Please select a destination:
-----------------------------
Start Here Before Posting
-----------------------------
=> Forum Rules And Information
-----------------------------
Information
-----------------------------
=> Introductions
-----------------------------
Ultra Sabers Discussion
-----------------------------
=> ANNOUNCEMENTS
=> Ultra Sabers General
=> Ultra Sabers Reviews
=> Ultra Sabers Gallery
=> Ultra Sabers Customization
=> Ultra Sabers Questions
=> The Obsidian Order
===> Obsidian Technical Discussion
===> Emerald Enclave
===> Diamond Database
===> Sound Fonts
-----------------------------
Way of the Saber
-----------------------------
=> Saber Artistry
=> Saber Combat
-----------------------------
General Chat
-----------------------------
=> Technical
=> Saberforum Chat
=> Star Wars
=> Off Topic
=> Costumes and Props
=> Events
=> Video Games
===> Old Republic Forum
=> Movies, TV, and Music
=> Forum Games
=> Bragging Rights
=> Videos
=> Fan Fiction and Art
Loading...